Differences

This shows you the differences between two versions of the page.

--- networking:fritzbox_3490 [2020/05/24 08:59] – created bstafford
+++ networking:fritzbox_3490 [2022/11/23 12:49] (current) – external edit 127.0.0.1
@@ Line 4: / Line 4: @@
 This will show the settings required to have the FritzBox own a /29 subnet and allow a dedicated firewall device to own the other five IP addresses.
- * Log into the WebGUI of the FritzBox
+  * Log into the WebGUI of the FritzBox
- * Switch to advanced view.
+  * Switch to advanced view.
- * Internet->Account Information->Internet Connection
+  * Internet->Account Information->Internet Connection
- * Set 'Internet service provider' = ''Other Internet Service Provider''
+  * Set 'Internet service provider' = ''Other Internet Service Provider''
- * Set 'Connect via' = ''Connection to a DSL line''
+  * Set 'Connect via' = ''Connection to a DSL line''
- * Set 'Account Information' = ''Yes''. Username (if using Zen Internet) = ''zen123456@zen''
+  * Set 'Account Information' = ''Yes''. Username (if using Zen Internet) = ''zen123456@zen''
- * Connection Settings - Internet Connection = ''Maintain Permanently (recommended for flat rates)''. Do not tick ''Delay disconnection by provider to the period between''
+  * Connection Settings - Internet Connection = ''Maintain Permanently (recommended for flat rates)''. Do not tick ''Delay disconnection by provider to the period between''
- * Tick ''Use VLAN for Internet access''
+  * Tick ''Use VLAN for Internet access''
- * Set VLAN-ID''101''
+  * Set VLAN-ID''101''
- * Set DSL ATM Settings''Set manually'' with VPI = ''1'', VCI = ''32'' and Encapsulation = ''PPPoE''
+  * Set DSL ATM Settings''Set manually'' with VPI = ''1'', VCI = ''32'' and Encapsulation = ''PPPoE''
- * Do not tick ''Connected network devices are also allowed to establish their own Internet connections (not recommended)''
+  * Do not tick ''Connected network devices are also allowed to establish their own Internet connections (not recommended)''
- * Go to Internet->Permit Access->Port Sharing
+  * Go to Internet->Permit Access->Port Sharing
- * Add Device for Sharing
+  * Add Device for Sharing
- * Set 'Device' to ''Enter the IP address manually''
+  * Set 'Device' to ''Enter the IP address manually''
- * Set 'IPv4 address' to one of the Public IP addresses you want the firewall to control
+  * Set 'IPv4 address' to one of the Public IP addresses you want the firewall to control
- * Tick 'Open this device completely for Internet sharing via IPv4 (exposed host).'
+  * Tick 'Open this device completely for Internet sharing via IPv4 (exposed host).'
- * Click 'OK'
+  * Click 'OK'
- * Repeat for each public IP.
+  * Repeat for each public IP.
 =====Configure IPv6=====
@@ Line 34: / Line 34: @@
 Then go to INTERNET > ACCOUNT INFORMATION and select
- * Connect to DSL Line (check box)
+  * Connect to DSL Line (check box)
- * Account information (No)
+  * Account information (No)
- * Connection Settings > Change Connection Settings
+  * Connection Settings > Change Connection Settings
- * * VLAN ID (101) for BT Fibre and Plusnet Fibre
+  *  * VLAN ID (101) for BT Fibre and Plusnet Fibre
- * *  Encapsulation > Routed Bridge Encapsulation and check the obtain the IP address automatically check box
+  *  *  Encapsulation > Routed Bridge Encapsulation and check the obtain the IP address automatically check box
 Then Select PPPoE Passthrough and check the 'Connected Devices are also allowed to their own Internet connection' box.